Head Office: 
Midlands: 
Northern: 
Manchester: 
Birmingham: 
Carlisle: 
Many building managers know they need fire compartmentation, but don't fully understand why, or what they're required to do about it as the responsible person. That's why we've put together this guide. 

How Does Fire Compartmentation Work? 

Fire compartmentation divides a building into manageable, fire-resistant zones, using walls and floors as barriers to stop fire and smoke spreading from one area to another. 
 
These barriers are built with materials and construction methods designed to resist fire for a specified period, depending on the building's use and risk profile. During this time, the compartment should remain intact, preventing flames, heat, and smoke from spreading into neighbouring areas. 

Fire Compartmentation Building Regulations 

Approved Document B, Volume 2 (2019) defines a fire compartment as: 
 
"A building or part of a building comprising one or more rooms, spaces or storeys constructed to prevent the spread of fire to or from another part of the same building or an adjoining building." 
 
In practice, this means walls, floors, doors and any service penetrations within a compartment need to be properly fire-rated and correctly installed. A compartment is only as effective as its weakest point. A single unsealed gap around a cable or pipe can undermine the protection the whole structure is meant to provide. 

Where is it required? 

Fire compartmentation building regulations must be followed in escape routes and high-risk rooms. It's also required in buildings with sleeping accommodation or high-occupancy areas such as flats, hotels and care homes. 
 
The specific requirements vary depending on the building's height, use and occupancy. Taller and higher-risk buildings typically need more stringent compartmentation standards. 

Why is it important? 

Fire compartmentation matters because it contains fire, heat and toxic smoke at the point of origin instead of them spreading freely through a building. This protects escape routes and gives occupants the time they need to evacuate safely. It also gives fire services a better chance of bringing the fire under control before it spreads further. 
 
Beyond life safety, compartmentation helps preserve the structural integrity of a building. By limiting how far fire can spread and how much heat builds up in any one area, it reduces the risk of structural collapse. It can significantly limit the extent of fire and smoke damage across the building as a whole. 

How is it surveyed? 

Fire compartmentation should be assessed by a third-party accredited company with experience in compartmentation surveys. A fire compartmentation survey will involve a detailed inspection of walls, floors, ceilings, fire doors and service penetrations to check that fire-resistant materials and seals are in place and undamaged. 
 
Surveyors look for breaches such as gaps around pipework, damaged or poorly maintained fire doors and unsealed service penetrations where cables or ducting pass through. 

What if my building doesn't have adequate fire compartmentation? 

If a survey shows your building's fire compartmentation is inadequate, you'll need to engage a competent contractor to carry out the necessary remedial work. This might involve replacing damaged fire doors, resealing service penetrations or repairing fire-rated walls and floors that have been compromised over time. 
 
As the responsible person, leaving these issues unaddressed isn't just a safety risk. It's also a breach of your legal duty under fire safety regulations. It could leave you personally liable if a fire were to spread beyond what the building's compartmentation should have contained. 

Key Components of Fire Compartmentation 

Fire compartmentation is a system of passive fire protection methods designed to contain fire and smoke within a defined area for a set period of time. 
 
Unlike active fire protection measures such as sprinklers or alarms, passive measures are built into the structure itself. They work simply by being in place and properly maintained. Several key components work together to form an effective compartment. 

Fire-resistant walls and floors 

These form the main structural barriers between compartments. They're built using materials capable of withstanding fire for a specified period, commonly 30, 60 or 90 minutes depending on the building's risk profile. 

Fire doors 

Fire doors are designed to hold back fire and smoke at openings in compartment walls, giving occupants time to escape while limiting how far a fire can spread. 

Cavity barriers 

Cavity barriers are installed within concealed spaces such as roof voids, ceiling voids and wall cavities to stop fire and smoke travelling unseen through a building. 

Fire stopping 

Fire stopping refers to the sealing of gaps and penetrations where pipes, cables, ductwork or other services pass through fire-resistant walls and floors. 

Dampers 

Where ventilation or ductwork passes through a compartment wall, fire dampers are fitted to automatically close in the event of a fire. They prevent flames and smoke from travelling through the ductwork into adjoining compartments. 

Common Causes of Fire Compartmentation Failure 

Even well-designed compartmentation can fail over time. Most failures aren't the result of poor initial construction but of what happens to a building after it's occupied. 

Building Alterations and Refurbishment Work 

When contractors install new cabling, pipework or ductwork, they often cut through fire-resistant walls and floors without reinstating fire stopping afterwards. They may not even realise they're working within a fire compartment. Unless the work is properly checked off, these breaches can go unnoticed for years. 

Damaged or Poorly Maintained Fire Doors 

Fire doors are vulnerable to everyday wear. Damaged seals, missing intumescent strips, faulty self-closers or doors that have been wedged open all reduce a fire door's ability to hold back fire and smoke when needed. 

Unsealed Service Penetrations 

Unsealed service penetrations tend to increase as buildings age and more cables, pipes and ducting are added. If these aren't sealed with appropriate fire-rated materials, they create direct pathways for fire and smoke to travel between compartments. 

Missing or Damaged Cavity Barriers 

Cavity barriers are easy to overlook, since they sit hidden within roof voids, ceiling voids and wall cavities. They can be removed or damaged during building works without this being visible during a routine walk-round. 

Lack of Ongoing Inspection 

Without regular checks, small defects such as a propped-open fire door or a partially sealed penetration can persist unnoticed. Gradually, they weaken the building's overall fire protection. 

Maintenance and Compliance for Fire Compartmentation 

Fire compartmentation isn't a one-off installation that can be checked off and forgotten. It needs ongoing maintenance throughout the life of a building, and as the responsible person, keeping on top of this is a legal duty rather than just good practice. 

Why Ongoing Maintenance Matters 

A compartment that passed its last survey with no defects can still fail. Issues can arise if a fire door is left wedged open, a new cable run is installed without resealing the wall, or a cavity barrier is disturbed. Because many of these defects are hidden, they're easy to miss without a structured routine in place. 

Routine Checks and Building Works 

Building managers should carry out regular visual checks of fire doors, looking for damaged seals, faulty self-closers and doors propped open or no longer closing fully. Visible service penetrations should also be checked periodically to confirm that fire stopping remains intact. When contractors carry out alterations involving cables, pipework or ductwork, fire-resistant walls or floors, they need to be reinstated to the correct standard once the work is finished. 

Periodic Surveys 

Alongside these checks, a full compartmentation survey should be carried out by a third-party accredited company at regular intervals. More frequent surveys are generally needed for higher-risk buildings such as those with sleeping accommodation or multiple occupancies. A survey should also be considered after any significant building works, even where those works weren't intended to affect fire-resistant elements directly. 

Record Keeping 

Survey reports, maintenance logs and details of remedial work should be kept as part of your wider fire safety documentation. These records demonstrate compliance and can be requested by enforcing authorities. 

Legal Duty 

Under the Regulatory Reform (Fire Safety) Order 2005, the responsible person has a legal duty to ensure compartmentation is properly maintained. Failing to do so can result in enforcement action. In serious cases, the prosecution of inadequate compartmentation can contribute to a fire spreading or putting lives at risk. 

Stay Compliant with Surveyed and High-Quality Fire Compartmentation 

Fire compartmentation divides a building into fire-resistant zones using walls and floors as barriers, containing fire, heat and smoke at the source for a specified period. This protects escape routes, gives occupants time to evacuate and helps preserve a building's structural integrity. 
 
It's a legal requirement in escape routes, high-risk rooms and buildings with sleeping accommodation or high occupancy. There are stricter standards for taller and higher-risk buildings. 
 
Most failures come not from poor construction but from changes afterwards, particularly building alterations, damaged fire doors and no ongoing inspection. The responsible person has a legal duty under the Regulatory Reform (Fire Safety) Order 2005 to keep compartmentation properly maintained. This maintenance comes from regular checks, periodic surveys and clear record-keeping. Failing to do so can result in enforcement action or prosecution. 
 
If you're unsure whether your building meets current standards, GRJ Contracting can help. As a Kiwa IFC, ASFP and ISO 9001 accredited contractor, GRJ offers survey, installation and certification services nationwide. Contact GRJ Contracting today for a fee quotation. 
Share this post:

Leave a comment: 

GRJ CONTRACTING 
GRJ Contracting Ltd was established in 2007 with the purpose of specialising in the design, supply, and installation of quality passive fire protection systems for the commercial and residential UK construction market. As an accredited company certified with Kiwa IFC, ASFP, ISO 9001, Cyber Essentials Plus, CHAS Advanced and SMAS based in the Midlands, we operate nationwide on new build and legacy construction projects of all scales and our range of services includes Intumescent Coatings and Rigid Boarding systems for Structural Steelwork protection, Service Penetration Firestopping, Mineral Fibre Boarding systems for internal building fire compartmentation and more. 
IFC Certification
Considerate Constructors Scheme
ISO 9001 Quality Management
ASFP
SafeContractor Approved
Constructionline Gold Member
CHAS Accredited Contractor
Terms of Use | Privacy | Cookies | Copyright © 2026 GRJ Contracting Ltd. All Rights Reserved. Branding by Carl Murch Design.